New Holland Discbine® 316 (flail)

NH Discbine316 2015

Discbine Disc Mower-Conditioners

 

CLOSER CUTTING, FASTER DRYDOWN, INCREASED DURABILITY
New Holland has taken the Discbine® mower-conditioner to a new level with two new center-pivot models. Combining both speed and performance, the new Discbine® 313 and Discbine® 316 feature increased durability, more efficient crop flow and smoother, more effective conditioning.

LARGER DISCS, WIDER CONDITIONING
The combination of larger cutting discs and a wider conditioning system leads to cleaner cutting, better crop flow, and more consistent drying. Co-rotating disc modules have been removed on the Discbine 313 and reduced to one pair on the Discbine 316. This greatly reduces the crop convergence between the cutterbar and the conditioner.

IMPROVED FLOTATION
Improved header attaching link geometry contributes to more responsive flotation. The rear pivot points of the header attaching links are lower than the pivot points on the front, ensuring the header moves up and back should you encounter an obstacle. In addition, the upper end of the flotation springs is anchored with a ball-and-socket arrangement that eliminates any binding as the header moves through its flotation range.

Model Discbine® 316 (flail)
New Holland-Disc Cutterbar  
Type MowMax™ II True Modular Disc Cutterbar
Width of Cut, ft. in. (m) 16' 3'' (4.95)
Number of discs 10
Number of knives 20 (2 per disc)
Disc Speed, rpm 2,250
Cutting angle 2 to 10 degrees
Hydraulic Cutting angle control  
Standard Cutting height skid shoe, in. (mm) 0.79-2.07 (20-69)
Fixed Raised, high-stubble skid shoe .79-5.75 (20- 146)
Adjustable Raised, high-stubble skid shoe 3-5.5 (76 - 140)
BioMass skid shoe 5-7.75 (127- 197)
Ground clearance with header fully raised, in. (mm) 16.2" (411)
Cutterbar Flotation Vertical and lateral, adjustable springs
QuickMax™ Knife Change System  
ShockPro™ Disc Drive Hub protection system  
MowMax™ 3-year cutterbar protection plan  
Chevron-Design Roll Conditioner  
Chevron-Design Roll Conditioner  
Type. Choice of molded rubber or steel rolls
Roll Length, in. (mm) 125 (3175)
Roll Diameter, in. (mm) 10.4 (264)
Roll Drive 4 HB V-belt and enclosed gears
Roll Speed, rpm Two-Speed: 750 or 640
Roll Pressure System Torsion Bar
Conditioner Intensity Adjustment Single crank adjustable roll pressure and two stop bolts to adjust roll gap
LeaningEdge™ Flail Conditioner  
LeaningEdge™ Flail Conditioner  
Number of LeaningEdge flails 120
Semi-Swinging LeaningEdge flail design  
Rotor Diameter, in. (mm) 22 (560)
Standard Speed, rpm 1042
Optional Slow Speed, rpm 752
Drive. 4 HB V-belt
Conditioner Intensity Adjustment. Single crank adjustable rotor hood
Optional Textured Hood Liner Kit  
Attachment  
Standard Drawbar -
Drawbar Swivel Hitch  
2-pt Swivel Hitch  
Dimensions  
Height, Transport, ft. in. (m) 7' 5" (2.26)
Height, Operating, ft. in. (m) 6' 7" (2.01)
Width, Transport, ft. in. (m) 16' 7" (5.05)
Width, Operating, Std. Drawbar Hitch, ft. in. (m) -
Width, Operating 2-pt Swivel Hitch, ft. in. (m) 25' 7" (7.8)
Width, Operating Drawbar Swivel Hitch, ft. in. (m) 19' 7'' (6.0)
Length, Transport, Standard Drawbar Hitch, ft. in. (m) -
Length, Transport, 2-pt Swivel Hitch, ft. in. (m) 32' 0'' (9.7)
Length, Transport, Drawbar Swivel Hitch, ft. in. (m) 31' 0'' (9.4)
Length, Operating, Standard Drawbar Hitch, ft. in. (m) -
Length, Operating, 2-pt Swivel Hitch, ft. in. (m) 26' 7'' (8.1)
Length, Operating Drawbar Swivel Hitch, ft. in. (m) 25' 7'' (7.8)
Weight, Operating lbs. (kg) 6,700 (3039)
Drive  
Drive 1000 rpm PTO, enclosed gears and four HB belt
Drive Protection  
Drive Protection Slip clutch and over-running clutch
Hydraulics  
Hydraulic swing Standard (double-acting cylinder)
Operating Position Center-Pivot, Right or Left Side
Hydraulic lift Standard (operated by two single-acting cylinders; master/slave)
Hydraulic tilt Standard (operated by single-acting cylinder and incorporated into the lift system)
Material Discharge  
Swath, ft. (mm) 10 (3000)
Windrow, ft. (mm) Adjustable from 3 to 8 (914 to 2400)
Wide Thin Fin Kit (100 % Coverage) -
Speeds  
Operating, mph (kph) 0 to 9 (0 to 14.5)
Transport, mph (kph) 20 (32)
Tractor Requirement  
Tractor Requirement 100 PTO hp (75 kW) or greater with standard ASAE Category III drawbar.
Hydraulic valves All models require two remote hydraulic valves capable of 1500 psi (10343 kPa), 7-pin SAE J560 connector for transport lights
Tubeless Ag Rib Implement Tires  
Size 12.5L x 15 8PR

Fields with asterisks* and highlighted red are required. Please email our helpful staff with any questions or comments using the contact form.

Fields with asterisks* and highlighted red are required. Your friend will receive an email that contains a reference to this page. Please send this email only to people you know who would be interested in this information.

Recent Listings

View All Inventory